Unit 2: Force and Translational Dynamics — A Free-Body Toolkit

Unit 2 of the algebra-based course, organised around a five-step attack on any force problem: choose the system, draw a free-body diagram where every arrow has a named agent, tilt the axes to the acceleration, write the second law one axis at a time, and check a limiting case. It covers systems and centre of mass, Newton's three laws and how to tell a third-law pair from balanced forces, the normal force and apparent weight in elevators, tension and Atwood machines, static and kinetic friction, inclines, springs and equilibrium, circular motion including flat and banked curves and hilltops, and Newton's law of gravitation. Every section ends on a homework-style problem. No calculus is used anywhere.

Subject: AP Physics 1 · 83 slides · diagram-first lesson

Open the interactive version of this deck

What this lesson covers

The lesson, slide by slide

1. AP Physics 1 — Force and Translational Dynamics

Title

Unit 2

A repeatable attack on force problems, from a box on a floor to a satellite

2. What this unit gives you

Objectives

Unit 1 described motion. This unit explains it: forces are what change motion, and the whole unit is one law applied to a steadily harder set of pictures. The aim, as before, is a method you can put on any homework problem, not a tour of the theory.

  1. Run the same five-step attack on any force problem, starting with the free-body diagram
  2. Draw a free-body diagram where every arrow has a named agent, and nothing is invented
  3. Tell a third-law pair from two forces that just happen to balance
  4. Find the normal force properly instead of assuming it equals the weight
  5. Solve connected-object problems: ropes, pulleys and Atwood machines
  6. Handle static and kinetic friction, including the case where nothing moves
  7. Tilt your axes to an incline and resolve the weight along and across it
  8. Treat circular motion as an ordinary second-law problem pointing at the centre
  9. Use Newton's law of gravitation to find g anywhere

College Board, AP Physics 1: Algebra-Based Course and Exam Description Unit 2, Force and Translational Dynamics

3. Part 1 — The method

Section

How to attack any force problem

4. One law, one method

Concept

Almost every problem in this unit is the same law: the net force on an object equals its mass times its acceleration. Students who struggle are rarely confused by the law. They are confused about which forces to put into it.

\[ \sum \vec{F} = m\vec{a} \]

So the method spends most of its effort before the equation. If the list of forces is right and the axes are sensible, the algebra that follows is usually two lines long.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.3

5. The five steps

Picture it

The force version of the Unit 1 method. Same idea: do the steps on easy problems so they are automatic when the problems get hard.

Figure (svg): A five-step vertical flow: choose the system, draw the free-body diagram, pick axes along the acceleration, write the second law per axis, then solve and check a limiting case

The check in step five is specific: set an angle to zero, a mass to zero or a friction coefficient to zero, and see whether your formula gives the obvious answer. It catches most sign errors and most swapped sines and cosines.

6. Predict: where do marks actually get lost?

Prediction

A guess about your own likely failure mode before we start.

Predict first

On a typical forces homework, which mistake costs the most marks?

  • Using the wrong value of g
  • A wrong free-body diagram: a force missing, or one that does not exist
  • Arithmetic slips in the final line
  • Forgetting the units

Correct: A wrong free-body diagram: a force missing, or one that does not exist

Why: Once the diagram is right, the rest is mechanical. The classic errors all happen in the diagram: drawing a force of motion that nothing exerts, forgetting the normal force on an incline, or drawing a centripetal force as an extra arrow. That is why the diagram gets its own section before any numbers appear.

7. Part 2 — Systems and free-body diagrams

Section

Steps one and two

8. Choose the system before anything else

Concept

A system is whatever you decide to draw a boundary around: one block, two blocks tied together, a person and the scale they stand on. Forces from outside the boundary are external; forces between parts inside it are internal and cancel in pairs.

free-body diagram — a dot standing for the system, with one arrow for every external force on it, each drawn from the dot in the direction it acts and labelled with what exerts it

Choosing a different system is a legitimate tool, not a trick. Two blocks tied together can be one system when you want the acceleration, and two separate systems when you want the tension between them.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.1, Systems and Center of Mass

9. A free-body diagram, done properly

Picture it

A box on a rough floor, pulled by a rope angled upward. Four forces act on it, and each one has an agent you can point at.

Figure (svg): On the left, a box on a floor pulled by a rope at thirty degrees; on the right, its free-body diagram with weight, normal force, tension and friction each labelled with its source

Only forces that act on the box appear. The box's pull on the rope, and the box's push on the floor, act on other objects and belong on their diagrams, not this one.

10. Draw it, or leave it off?

Definition probe

The rule: a force belongs on the diagram only if you can name the object that exerts it.

Sort into buckets

A hockey puck slides across ice after leaving the stick. Which of these go on its free-body diagram?

draw it
Its weight; The normal force from the ice; Kinetic friction from the ice
leave it off
The force of the stick, which is still keeping it moving; The force of motion; Its inertia, pushing it forward
yes
Each has an agent touching or attracting the puck right now: the Earth pulls it down, the ice pushes it up, and the ice rubs against its motion. Those are the only three forces it feels once it is sliding.
no
None of these has an agent. The stick stopped touching the puck the moment it left, and there is no force of motion or force of inertia: an object keeps moving without any force at all. That is precisely what the first law says.

11. Match every force to its agent

Matching

Every force in this unit is one of six kinds, and each kind has a typical source. Knowing the list stops you inventing a seventh.

Match the pairs

  • a1. weight
  • a2. normal force
  • a3. tension
  • a4. friction
  • a5. spring force
  • a6. applied force
  • b1. the Earth, at a distance
  • b2. a surface, pushing straight out of itself
  • b3. a rope or string, pulling along itself
  • b4. a surface, along itself, opposing sliding
  • b5. a stretched or squashed spring
  • b6. a person or machine pushing or pulling

Why: Weight is the only force here that acts without contact. Every other one needs something touching the object, so a quick check on any diagram is to ask: what is touching it? Each thing touching it supplies at most a normal force and a friction force, or a tension, and nothing else.

12. Worked example: the centre of mass

Worked example

A light rod 4.0 m long has a 2.0 kg mass at one end and a 6.0 kg mass at the other. Where is the centre of mass, measured from the lighter end?

Figure (svg): A rod with a two kilogram mass at zero metres and a six kilogram mass at four metres, with the centre of mass marked at three metres

Put an axis on the rod

Why: Origin at the lighter mass, positive toward the heavier one.

Weight each position by its mass, then divide by the total mass

Why: This is a weighted average of the positions.

\[ x_{\text{cm}} = \dfrac{m_1 x_1 + m_2 x_2}{m_1 + m_2} = \dfrac{(2.0)(0) + (6.0)(4.0)}{8.0} = 3.0 \text{ m} \]

Verify: by balancing the rod

Why: Pivot the rod at 3.0 m. The light mass is 3.0 m away and the heavy one 1.0 m away, and 2.0 times 3.0 equals 6.0 times 1.0. Equal turning effects on each side means the rod balances there, which is exactly what a centre of mass is.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 8.5

13. Test the claim: moving things need a force to keep moving

Counterexample

The single most persistent wrong idea in mechanics, and it is worth taking apart properly.

Discussion prompt

A student says a car cruising at a steady 25 m/s on a level road must have a net forward force on it, or it would slow down. Find what is wrong with the claim.

Hint: Separate the forward force from the net force.

Answer:

The car does have a forward force on it: friction from the road on the driven wheels. But it also has air resistance and rolling resistance acting backward, and at a steady speed those exactly cancel the forward force.

So the net force is zero, which is exactly what constant velocity requires. A net force would make the car speed up.

The intuition comes from a world full of friction, where stopping the engine means slowing down. Remove the friction, as on ice or in space, and an object keeps moving with no force at all.

14. Part 3 — Newton's three laws

Section

Step four, and the pairs that confuse everyone

15. The first law: no net force, no change in velocity

Concept

An object with zero net force keeps whatever velocity it has, including zero. That covers two different-looking situations which are physically identical: a book at rest on a table, and a puck gliding at constant velocity on frictionless ice.

\[ \sum \vec{F} = 0 \quad \Longleftrightarrow \quad \vec{v} \text{ constant} \]

This is the most common starting point in the homework. Whenever a problem says at rest, at constant speed in a straight line, or in equilibrium, write net force equals zero along each axis and you have your equations.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.2

16. The second law, one axis at a time

Concept

When the forces do not cancel, the acceleration points along the net force and its size is the net force divided by the mass. In practice you never use the vector form directly. You split it into two ordinary equations.

\[ \sum F_x = m a_x \qquad \sum F_y = m a_y \]

Choose one axis along the direction the object accelerates. Then the other equation usually has zero on its right-hand side, which is what lets you find the normal force or a tension before tackling the axis where things happen.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.7, Newton's Second Law

17. Same push, different masses

Picture it

The second law in one picture: mass is the resistance to having your velocity changed.

Figure (svg): A twenty newton push giving a two kilogram block an acceleration of ten metres per second squared and a ten kilogram block two metres per second squared

Five times the mass gives one fifth of the acceleration for the same force. That inverse relationship is what the word inertia means, and it is a property of the object, not a force acting on it.

18. At the top of the throw

Anomaly

A ball thrown straight up has just reached its highest point. This links back to Unit 1.

Predict first

Which forces act on the ball at that instant, ignoring air resistance?

  • None, because it is momentarily at rest
  • Its weight only
  • Its weight and an upward force from the throw
  • An upward and a downward force that balance

Correct: Its weight only

Why: The hand stopped touching the ball when it was released, so the upward force of the throw is gone. Only the Earth still acts on it. That single downward force is exactly why the acceleration at the top is 9.8 downward, as Unit 1 found: the second law and the kinematics agree.

19. The third law: forces come in pairs, on different objects

Concept

If object A pushes on object B, then B pushes on A with a force of the same size in the opposite direction. The two forces are the same kind of force, appear and disappear together, and act on different objects.

\[ \vec{F}_{A \text{ on } B} = -\vec{F}_{B \text{ on } A} \]

The phrase that matters is different objects. Because the two forces of a pair act on different bodies, they never both appear on the same free-body diagram, so they can never cancel each other.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.4

20. Pairs versus balanced forces

Picture it

The book on the table is the standard test, and most students get it wrong the first time.

Figure (svg): A book on a table with its weight and normal force drawn, and a panel listing the two true third-law pairs: Earth and book, and table and book

The weight and the normal force on the book are equal and opposite, but that is because the book is in equilibrium, not because of the third law. Put the table in an accelerating elevator and they stop being equal, while each third-law pair stays exactly equal.

21. Two truths and a lie about the book

Two truths and a lie

A book rests on a table.

Eliminate the wrong options

Cross out the false statement.

  • t1. The book pulls the Earth upward exactly as hard as the Earth pulls the book down.
  • t2. The normal force on the book equals its weight because the book is not accelerating.
  • t3. The normal force and the weight are a third-law pair.

Survives elimination: t3

Why: They act on the same object, the book, and they are different kinds of force: one is a contact push from the table, the other is gravity from the Earth. A third-law pair never acts on the same object and is always the same kind of force, so this pairing fails both tests.

22. The pattern: third-law pair or just balanced?

Pattern

Two equal and opposite forces can be related in two completely different ways. These tests tell them apart every time.

testthird-law pairbalanced forces
which objects do they act ontwo different objectsthe same object
are they the same kind of forcealwaysnot necessarily
are they always equalyes, even during a crashonly if the object is not accelerating
do they appear on one free-body diagramneveryes, both
which law explains themthe thirdthe first or second

Read the third row twice. Third-law pairs stay equal no matter what is accelerating, which is what makes the next question feel so wrong.

HyperPhysics, Mechanics — Newton's laws, friction and circular motion Newton's third law

23. Check: the truck and the car

Check

Solve it on paper before you click.

Check your understanding

A heavy truck collides head-on with a small car. During the collision, how does the force of the truck on the car compare with the force of the car on the truck?

  • A. The truck exerts a much larger force, because it is heavier
  • B. The car exerts a larger force, because it is moving faster
  • C. The forces are exactly equal in size (correct)
  • D. It depends on which one was moving faster

Answer: C

Why: They are a third-law pair, so they are equal in size and opposite in direction at every instant of the collision, whatever the masses and speeds. The car is wrecked because the same force acting on a smaller mass produces a much larger acceleration: the second law, not a larger force.

Why A tempts people
Mass changes the effect of the force, through the acceleration, not the size of the force. The third law has no exceptions for heavy objects.
Why B tempts people
Speed does not enter the third law at all. The forces are equal regardless of how fast either vehicle was going.
Why D tempts people
This sounds like a careful answer, but the third law holds for every interaction at every instant, so nothing about the motion can make the pair unequal.

24. Worked example: two blocks pushed together

Worked example

A 24 N push acts on a 4.0 kg block, which pushes a 2.0 kg block ahead of it across a frictionless floor. Find the acceleration and the force between the blocks.

Figure (svg): A twenty-four newton push on a four kilogram block pushing a two kilogram block, with an acceleration of four metres per second squared and an eight newton contact force on the smaller block

System one: both blocks together

Why: The contact forces between the blocks are internal, so they cancel and only the 24 N push is external.

\[ a = \dfrac{24}{4.0 + 2.0} = 4.0 \text{ m/s}^2 \]

System two: the 2.0 kg block on its own

Why: Now the contact force from the big block is external, and it is the only horizontal force on the small one.

\[ F_{\text{contact}} = (2.0)(4.0) = 8.0 \text{ N} \]

Verify: with the other block

Why: The big block feels the 24 N push forward and, by the third law, 8.0 N backward from the small block. Its net force is 16 N, and 16 divided by 4.0 is 4.0 m/s squared, the same acceleration. Three systems, one answer.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.6

25. Part 4 — Weight, normal force and apparent weight

Section

The force everyone assumes

26. Weight is fixed; the normal force adjusts

Concept

Weight is the Earth's pull, the mass times g, and near the surface it does not change. The normal force is different in kind: a surface pushes back exactly as hard as it needs to so that the object does not sink into it.

\[ W = mg \qquad N = \text{whatever the second law requires} \]

So never write the normal force as m g out of habit. Find it from the perpendicular axis of the second law. It equals m g only when nothing else pushes or pulls perpendicular to the surface and nothing accelerates that way.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.3, Gravitational and Normal Forces

27. The same box, three normal forces

Picture it

A 5.0 kg box, so the weight is 49 N in every panel. Watch the normal force change.

Figure (svg): Three free-body diagrams of a five kilogram box: resting with a forty-nine newton normal force, pushed down with twenty newtons giving sixty-nine, and pulled up at thirty degrees giving thirty-nine

Pushing down makes the floor push back harder. Pulling partly upward does some of the floor's job, so the floor pushes back less. In both cases the weight never changed.

28. Estimate: the angled pull

Estimation

This is the version that matters for friction later, so commit to a number first.

Predict first

The 5.0 kg box is pulled with 20 N at 30 degrees above horizontal. Roughly what is the normal force?

  • About 59 N
  • About 49 N
  • About 39 N
  • About 29 N

Correct: About 39 N

Why: The vertical part of the pull is 20 times the sine of 30, which is 10 N upward. The floor and the pull together hold up the 49 N box, so the floor supplies only 39 N. Writing 49 here is the single most common error in angled-pull friction problems, because friction depends on this number.

29. Worked example: the elevator scale

Worked example

A 60 kg student stands on a bathroom scale in an elevator that accelerates upward at 2.0 m/s squared. What does the scale read?

Figure (svg): A person on a scale in an elevator accelerating upward, with a free-body diagram showing a 708 newton normal force up and a 588 newton weight down

System: the student. Axis: up is positive

Why: Up is the direction of the acceleration, so the second law has a positive right-hand side.

Two forces: the scale pushes up, the Earth pulls down

Why: The scale reading is the size of the normal force, because that is the force the scale feels pressing on it.

\[ N - mg = ma \]

\[ N = m(g + a) = 60(9.8 + 2.0) = 708 \text{ N} \]

Verify: with limiting cases

Why: Set a to zero and the scale reads 588 N, the true weight, as it should when the elevator is still or moving at constant speed. Set a to negative 9.8, free fall, and the reading is zero. Both limits are right, so the formula is trustworthy.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.6, example on apparent weight

30. Heavier, lighter or the same?

Discrimination

Use the direction of the acceleration, not the direction of motion. Two of these catch almost everyone.

Sort into buckets

Compared with standing still, does the scale read more, less or the same?

reads more
Elevator starting to go up; Elevator slowing down while going down
reads less
Elevator slowing down while going up; Elevator starting to go down
reads the same
Elevator moving up at constant speed; Elevator moving down at constant speed
more
The acceleration points up, so the floor has to push harder than the weight. That includes slowing down on the way down, which feels odd until you notice the acceleration is upward.
less
The acceleration points down, so the floor pushes less than the weight. That includes slowing down on the way up, where the motion is upward but the acceleration is not.
same
Constant velocity means zero acceleration, so the normal force equals the weight exactly. The direction of motion does not matter at all.

31. Why do astronauts float?

Socratic

A question worth reasoning through, because the usual answer, no gravity up there, is wrong.

Discussion prompt

On the space station, gravity is still about 89 per cent of its strength at the surface. So why does an astronaut on a scale read zero?

Hint: What did the elevator formula give when a equals negative g?

Answer:

Because the station and everything in it are in free fall together. They are falling around the Earth, not away from it.

The elevator formula already gave the answer: when the acceleration is g downward, the normal force is zero. The scale is falling just as fast as the astronaut, so it never presses on her feet.

Weightless means no normal force, not no gravity. Gravity is the very thing keeping the station in orbit, as Part 9 will show.

32. Part 5 — Tension and connected objects

Section

Ropes, pulleys and Atwood machines

33. What an ideal rope and pulley do

Concept

Tension is the pull a rope exerts along its own length, always pulling away from whatever it is tied to. Problems at this level use an ideal rope, massless and unstretchable, and an ideal pulley, massless and frictionless.

Those three facts are what let you write one unknown tension and one unknown acceleration for the whole system, so two equations are always enough.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.5, Tension

34. The modified Atwood machine

Picture it

The most common connected-object problem in AP Physics 1, and the template for all the others.

Figure (svg): A three kilogram block on a frictionless table tied over a pulley at the edge to a two kilogram hanging block, with the tension and the acceleration marked on both

Choose positive in the direction the system moves: right for the table block, down for the hanging one. Then a single acceleration is positive for both and the signs take care of themselves.

35. Worked example: the modified Atwood machine

Worked example

A 3.0 kg block on a frictionless table is tied over a pulley to a hanging 2.0 kg block. Find the acceleration and the tension.

Figure (svg): A three kilogram block on a table tied over a pulley to a hanging two kilogram block

Whole system first, positive along the motion

Why: Only the hanging block's weight drives the system. The tension is internal, and the table block's weight is cancelled by the table.

\[ a = \dfrac{m_2 g}{m_1 + m_2} = \dfrac{(2.0)(9.8)}{5.0} = 3.92 \text{ m/s}^2 \]

Then the table block alone, for the tension

Why: The rope is the only horizontal force on it.

\[ T = m_1 a = (3.0)(3.92) = 11.8 \text{ N} \]

Verify: with the hanging block

Why: Its weight is 19.6 N down and the tension 11.8 N up, a net of 7.84 N down. Divided by 2.0 kg that is 3.92 m/s squared, matching. Note too that the tension is less than the hanging weight, which it must be, or the block would not accelerate downward.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.6

36. Trap: setting the tension equal to the hanging weight

Trap

The trap

Same setup: 3.0 kg on the table, 2.0 kg hanging. Find the tension.

The rope holds up the hanging block, so the tension is its weight

Why: That gives 2.0 times 9.8, which is 19.6 N.

Then the table block accelerates at 19.6 divided by 3.0

Why: That is 6.53 m/s squared, which does not match anything, and the error is invisible from here.

The fix

Same setup: 3.0 kg on the table, 2.0 kg hanging. Find the tension.

The hanging block is accelerating, so its forces cannot balance

Why: If tension equalled its weight, the net force on it would be zero and it would not fall. Tension equals the weight only when nothing accelerates.

Solve the two second-law equations together

Why: This gives 3.92 m/s squared and 11.8 N, and the tension is correctly less than 19.6 N.

37. The standard Atwood machine

Picture it

Two hanging masses, 5.0 kg and 3.0 kg, over one pulley.

Figure (svg): A five kilogram and a three kilogram mass hanging on either side of a single pulley, the heavier one accelerating down and the lighter one up

The net driving force is the difference of the weights, and it accelerates the total mass. The tension sits between the two weights: more than the light one, less than the heavy one.

38. Fill the middle: the Atwood machine

Fill the middle

Use the whole-system shortcut, then one block for the tension. Take g as 9.8.

Fill in the blanks

a = \dfrac2.45 m/s^236.8 N = ___ \qquad T = 3.0(9.8 + a) = ___

Why: The difference in weights is 19.6 N, driving 8.0 kg, so a is 2.45. The 3.0 kg block rises, so the tension must exceed its weight: 3.0 times 12.25 is 36.75 N. Check with the 5.0 kg block: 5.0 times the quantity 9.8 minus 2.45 is also 36.75 N.

39. Faded example: a train of blocks

Faded example

A 20 N pull drags a 3.0 kg block, which drags a 2.0 kg block behind it by a rope, across a frictionless floor.

Fill in the blanks

a = \dfrac4.0 m/s^28.0 N = ___ \qquad T = (2.0)(a) = ___

Why: Same structure as the pushed blocks: the whole system for the acceleration, then the block with only one horizontal force for the tension. The rear block is the easy choice because the rope is the only thing pulling it, so its equation has one unknown.

40. Order the connected-objects attack

Ranking

This order is what keeps a two-block problem to four lines.

Put in order

  1. Draw each block and choose positive along the direction of motion
  2. Decide which forces are internal and cancel
  3. Write the second law for the whole system to get the acceleration
  4. Write the second law for one block to get the tension
  5. Check with the block you did not use

Why: Draw first so the signs are settled, and pick positive along the motion so one acceleration works for every block. Then identify internal forces, because ignoring them is what makes the whole-system equation have only one unknown. The single-block equation brings the tension back in, and the unused block is a free check.

41. Part 6 — Friction

Section

The force with a range

42. Static and kinetic friction are different kinds of rule

Concept

Kinetic friction acts when surfaces slide over each other, and it has one value: the coefficient of kinetic friction times the normal force, directed against the sliding.

\[ f_k = \mu_k N \]

Static friction acts when they do not slide, and it is not a single value. It takes whatever size is needed to stop sliding, up to a maximum. That inequality is the most misused formula in the unit.

\[ f_s \le \mu_s N \]

So static friction is found from the second law, not from the formula. The formula only tells you the ceiling, the point where the object starts to slip.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 5.1

43. Friction as you push harder

Picture it

A 10 kg crate with a static coefficient of 0.50 and a kinetic one of 0.30. Push gradually harder and record the friction.

Figure (svg): A graph of friction against applied push: friction rises equal to the push up to forty-nine newtons, then drops to a constant twenty-nine point four newtons once sliding begins

Below 49 N the crate stays put and friction exactly matches your push. Past 49 N it breaks free, friction drops to the kinetic value, and the leftover push accelerates it. The drop is why a heavy object is hardest to get moving.

44. Predict: a push that is too small

Prediction

The same crate: maximum static friction 49 N.

Predict first

You push the crate with 30 N and it does not move. What is the friction force?

  • 49 N
  • 30 N
  • 29.4 N
  • Zero, because nothing moves

Correct: 30 N

Why: The crate is in equilibrium, so the net horizontal force is zero and friction must exactly cancel your 30 N push. The 49 N is only the most static friction could supply. Using it here would mean a net 19 N backward force on a crate that is sitting still, which is impossible.

45. Worked example: the push that wins

Worked example

Now you push the 10 kg crate with 60 N. The kinetic coefficient is 0.30. Find its acceleration.

Figure (svg): Free-body diagram of the crate with a sixty newton push, twenty-nine point four newton friction, and ninety-eight newton weight and normal force

Does it move?

Why: Maximum static friction is 0.50 times 98, which is 49 N. The push of 60 N exceeds that, so it slides and kinetic friction applies.

Vertical axis first: nothing accelerates vertically

Why: So the normal force equals the weight, 98 N, because no other force is vertical.

\[ f_k = \mu_k N = (0.30)(98) = 29.4 \text{ N} \]

Horizontal axis: net force equals m a

Why: The push drives it forward and kinetic friction opposes it.

\[ a = \dfrac{60 - 29.4}{10} = 3.06 \text{ m/s}^2 \]

Verify: with a limiting case

Why: With no friction the acceleration would be 60 over 10, which is 6.0 m/s squared. With friction it should be less, and it is roughly half, since friction takes away roughly half the push. The size and the direction both make sense.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 5.1, example on sliding friction

46. Worked example: pulling at an angle

Worked example

A 10 kg box is pulled across a floor by a rope at 37 degrees above horizontal with a tension of 50 N. The kinetic coefficient is 0.20. Find the acceleration. Use sine 0.60 and cosine 0.80.

Figure (svg): Free-body diagram of the box: fifty newtons at thirty-seven degrees split into forty horizontal and thirty vertical, a sixty-eight newton normal force, ninety-eight newton weight and thirteen point six newton friction

Resolve the pull

Why: Horizontal 50 times 0.80, which is 40 N. Vertical 50 times 0.60, which is 30 N upward.

Vertical axis: find the normal force first

Why: No vertical acceleration, so the upward forces equal the downward one.

\[ N + 30 = 98 \;\Rightarrow\; N = 68 \text{ N} \]

\[ f_k = (0.20)(68) = 13.6 \text{ N} \]

Horizontal axis

Why: The 40 N component drives it and friction opposes it.

\[ a = \dfrac{40 - 13.6}{10} = 2.64 \text{ m/s}^2 \]

Verify: with the zero-angle limit

Why: At zero degrees the whole 50 N is horizontal and the normal force is the full 98 N, so friction is 19.6 N and a is 3.04 m/s squared. Tilting the rope loses 10 N of forward pull but saves 6 N of friction, so the angled pull should give a little less, and 2.64 is a little less.

HyperPhysics, Mechanics — Newton's laws, friction and circular motion friction on a level surface

47. Find the error in this homework solution

Error analysis

The same angled-pull problem, as one student wrote it.

Annotate

On: \( f_k = \mu_k m g = (0.20)(10)(9.8) = 19.6 \text{ N}, \quad a = \dfrac{40 - 19.6}{10} = 2.04 \text{ m/s}^2 \)

  • The friction formula uses the normal force, and the student has replaced it with m g out of habit. Here the rope lifts 30 N of the weight, so the normal force is 68 N, not 98 N.
  • That one substitution inflates friction from 13.6 N to 19.6 N and drags the answer from 2.64 down to 2.04, an error of over 20 per cent.
  • Everything after the first equals sign is correct arithmetic, which is what makes this error so hard to spot by checking the working. It has to be caught at the diagram.

This is why the method always does the perpendicular axis first. The normal force comes out of that equation, and friction cannot be written down until it has.

48. Does a wider tyre give more friction?

Hypothesis

Test the friction model against an everyday intuition.

Predict first

Two identical bricks slide across the same floor, one lying flat and one standing on its narrow end. Which has more kinetic friction?

  • The flat one, because more surface is touching
  • The one on its end, because the pressure is higher
  • They are equal
  • It depends on the speed

Correct: They are equal

Why: In the model, friction depends only on the coefficient and the normal force, and both bricks have the same normal force. Contact area does not appear. Physically, the flat brick has more area but presses each part of it more lightly, and the two effects cancel. Real racing tyres are wide for heat and wear reasons that lie outside this model.

49. Part 7 — Inclines

Section

Tilt the axes, not the problem

50. The one move that makes inclines easy

Concept

On a slope the object accelerates along the slope, so step three of the method says to put one axis along the slope and the other perpendicular to it. Then the normal force and friction already lie along the axes.

Only the weight is at an angle to these axes, so it is the only force you resolve. The part along the slope pulls the object down it; the part into the slope is what the normal force has to balance.

\[ W_{\parallel} = mg\sin\theta \qquad W_{\perp} = mg\cos\theta \]

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 5.1, inclined planes

51. The weight on a slope, resolved

Picture it

Read off which component gets sine and which gets cosine, because swapping them is the standard error.

Figure (svg): A block on a thirty degree incline with its weight drawn straight down and resolved into a component down the slope, m g sine thirty, and a component into the slope, m g cosine thirty, with the normal force and friction drawn

A quick way to remember: as the slope flattens to zero degrees, the along-the-slope part must vanish and the into-the-slope part must become the whole weight. Sine of zero is zero and cosine of zero is one, so sine goes along the slope.

52. Steepen the slope

Tweak it

A block sliding down an incline, with a kinetic coefficient you can change. The curve shows its acceleration against the angle.

Parameter explorer

Drag the coefficient. Where does the curve leave zero, and what is the acceleration at 90 degrees?

\[ a = 9.8(\sin\theta - {mu}\cos\theta) \]

  • mu — from 0 to 1: kinetic coefficient

53. Worked example: sliding down a rough slope

Worked example

A 5.0 kg block slides down a 30 degree incline with a kinetic coefficient of 0.20. Find its acceleration.

Figure (svg): A block on a thirty degree incline with its weight resolved along and into the slope, and the normal force and friction drawn

Axes along and perpendicular to the slope

Why: Positive down the slope, the direction it accelerates.

Perpendicular axis first

Why: No acceleration across the slope, so the normal force balances the into-the-slope part of the weight.

\[ N = mg\cos 30^\circ = (5.0)(9.8)(0.866) = 42.4 \text{ N} \]

\[ f_k = (0.20)(42.4) = 8.49 \text{ N} \]

Along the slope

Why: The along-the-slope part of the weight drives it and friction opposes it.

\[ a = \dfrac{(5.0)(9.8)(0.5) - 8.49}{5.0} = \dfrac{24.5 - 8.49}{5.0} = 3.20 \text{ m/s}^2 \]

Verify: with the general formula

Why: Dividing everything by the mass gives g times the quantity sine 30 minus 0.20 cosine 30, which is 9.8 times 0.327, or 3.20 m/s squared. The mass cancelled, so a 50 kg block would slide with the same acceleration, just as a heavy and light object fall together.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 5.1

54. When does a block start to slip?

Socratic

A classic lab result, and a neat way to measure a coefficient with nothing but a protractor.

Discussion prompt

Tilt a board slowly until a block resting on it just begins to slide. Why does the angle alone tell you the static coefficient?

Hint: Set the maximum static friction equal to the along-the-slope pull and see what survives.

Answer:

Just before it slips, static friction is at its maximum and exactly balances the along-the-slope pull: the coefficient times m g cos theta equals m g sin theta.

The mass and g cancel, leaving the coefficient equal to the tangent of the angle. So a block that slips at 21.8 degrees has a static coefficient of 0.40.

The mass cancelling is the important part: a heavier block slips at the same angle, because both the pull down the slope and the maximum friction grow in proportion to the weight.

55. Check: friction on a block that is not moving

Check

Solve it on paper before you click.

Check your understanding

A 5.0 kg block sits at rest on a 30 degree incline. The static coefficient is 0.70. What is the friction force on it?

  • A. 24.5 N (correct)
  • B. 29.7 N
  • C. 42.4 N
  • D. 49 N

Answer: A

Why: The block is in equilibrium, so friction exactly balances the along-the-slope part of the weight: 5.0 times 9.8 times the sine of 30, which is 24.5 N. The coefficient only sets the ceiling of 29.7 N, and since 24.5 is below that ceiling, the block indeed stays put.

Why B tempts people
That is the maximum static friction, 0.70 times 42.4. Static friction only reaches its maximum at the point of slipping, and this block is nowhere near slipping.
Why C tempts people
That is the normal force, the into-the-slope part of the weight. Friction acts along the slope, not into it.
Why D tempts people
That is the whole weight. Only the along-the-slope component needs balancing by friction; the rest is balanced by the normal force.

56. Part 8 — Springs and equilibrium

Section

When the net force is zero

57. Hooke's law: the spring force

Concept

A spring pulls or pushes back in proportion to how far it is stretched or squashed from its natural length. The constant of proportionality, k, is the spring's stiffness, measured in newtons per metre.

\[ F_s = kx \]

The direction is always back toward the natural length, which is why it is called a restoring force. That restoring property is what makes springs oscillate, and Unit 7 is built on it.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.6, Spring Forces

58. Fill the middle: a hanging spring

Fill the middle

A 2.0 kg mass hangs at rest from a spring and stretches it 0.20 m. At rest, the spring force balances the weight.

Fill in the blanks

k = \dfrac98 N/m0.30 m = ___ \qquad x____} = \dfrac______ = ___

Why: The weight of 19.6 N stretches the spring 0.20 m, so k is 98 N/m. A 3.0 kg mass weighs 29.4 N, and dividing by 98 gives 0.30 m. One and a half times the weight, one and a half times the stretch, which is what proportional means.

59. The stretch is proportional to the load

Picture it

The same spring with no load, 2.0 kg and 3.0 kg.

Figure (svg): One spring shown unloaded, stretched twenty centimetres by two kilograms, and thirty centimetres by three kilograms

A spring is a force meter: read the stretch and you know the force. That is literally how a spring scale and a bathroom scale work.

60. Worked example: a sign on two ropes

Worked example

A 100 N sign hangs from a knot held by two ropes, each at 30 degrees above the horizontal. Find the tension in each rope.

Figure (svg): A one hundred newton sign hanging from a knot held by two ropes each at thirty degrees above horizontal, each with a tension of one hundred newtons

System: the knot, which is in equilibrium

Why: Three forces act on it: the two rope tensions and the downward pull of the sign.

Horizontal axis

Why: The two ropes are symmetric, so their horizontal parts cancel and the tensions are equal.

Vertical axis: each rope lifts only its vertical component

Why: Each rope contributes T times the sine of 30, and together they must hold up the 100 N sign.

\[ 2T\sin 30^\circ = 100 \;\Rightarrow\; T = \dfrac{100}{2(0.5)} = 100 \text{ N} \]

Verify: with the limiting cases

Why: If the ropes hung straight down, each would carry 50 N, half the sign. At 30 degrees each carries 100 N, and as the angle flattens toward zero the sine heads to zero and the tension heads to infinity. That is why a washing line can never be pulled perfectly straight.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 4.7

61. Wager: steep ropes or shallow ropes?

Commit first

Bet on it before calculating.

Predict first

Hang the same 100 N sign from ropes at 60 degrees above horizontal instead of 30. What happens to the tension?

  • It rises above 100 N
  • It falls to about 58 N
  • It stays at 100 N
  • It falls to 50 N

Correct: It falls to about 58 N

Why: Each rope now lifts T times the sine of 60, which is 0.866 T. Two of them must make 100 N, so T is 100 divided by 1.73, about 57.7 N. Steeper ropes do more lifting per newton of tension, so less tension is needed. The minimum, 50 N each, comes when the ropes hang straight down.

62. Part 9 — Circular motion

Section

The second law, pointed at the centre

63. Circular motion needs a net force toward the centre

Concept

An object moving in a circle at constant speed is accelerating, because its direction keeps changing. That acceleration points to the centre of the circle and has a definite size.

\[ a_c = \dfrac{v^2}{r} \]

By the second law, something must supply a net force toward the centre of exactly m times that. This is not a new kind of force. It is a job that tension, gravity, friction or a normal force has to do, and the free-body diagram contains only those real forces.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.9, Circular Motion

64. Velocity along the path, acceleration toward the centre

Picture it

The two arrows are perpendicular at every point, which is why the speed never changes.

Figure (svg): An object on a circular path with its velocity tangent to the circle and its acceleration pointing toward the centre, and a panel explaining that a real force provides the centripetal acceleration

If the string breaks, the inward force vanishes and the object carries on in a straight line along the tangent. There is no outward force to throw it outward; the outward feeling on a ride is your body trying to go straight.

65. What supplies the centripetal force?

Translation

In every case, find the real force that points toward the centre.

Match the pairs

  • s1. A car rounding a flat curve
  • s2. The Moon orbiting the Earth
  • s3. A ball whirled on a string in a horizontal circle
  • s4. A car on a banked, icy curve
  • s5. Clothes in a spinning washing-machine drum
  • r1. static friction from the road
  • r2. gravity
  • r3. tension
  • r4. the horizontal part of the normal force
  • r5. the normal force from the drum wall

Why: Five different forces doing one job. In each case the free-body diagram shows only the real force, and the second law along the inward direction sets that force equal to m v squared over r. The tilted road is the subtle one: on ice there is no friction, so the slope itself has to turn the car, through the sideways tilt of the normal force.

66. Worked example: the fastest safe speed on a flat curve

Worked example

A 1200 kg car rounds a flat curve of radius 50 m. The static coefficient between tyres and road is 0.80. What is the highest speed at which it can take the curve without skidding?

Figure (svg): A car on a flat curve seen from behind, with the normal force up, the weight down, and static friction pointing toward the centre of the curve

Inward axis: friction is the only horizontal force

Why: It must supply the centripetal force, and at the fastest safe speed it is at its maximum.

Vertical axis: the normal force equals the weight

Why: The road is flat and nothing accelerates vertically.

\[ \mu_s mg = \dfrac{mv^2}{r} \;\Rightarrow\; v = \sqrt{\mu_s g r} \]

\[ v = \sqrt{(0.80)(9.8)(50)} = \sqrt{392} = 19.8 \text{ m/s} \]

Verify: with the units and the mass

Why: Under the root, a pure number times metres per second squared times metres gives metres squared per second squared, so the answer is a speed. The 1200 kg cancelled, so a lorry and a bicycle have the same limit on the same road, which is why curve speed signs do not depend on the vehicle.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 6.3

67. Worked example: over the top of a hill

Worked example

A 1000 kg car drives over the crest of a hill whose top is a circular arc of radius 20 m, at 10 m/s. What normal force does the road exert? At what speed would the car leave the road?

Figure (svg): A car at the crest of a hill with a 9800 newton weight down, a 4800 newton normal force up, and a 5.0 metre per second squared acceleration toward the centre below

Choose positive toward the centre, which is downward

Why: The acceleration points down, so the weight helps and the normal force opposes.

\[ mg - N = \dfrac{mv^2}{r} \]

\[ N = 9800 - \dfrac{(1000)(10)^2}{20} = 9800 - 5000 = 4800 \text{ N} \]

The car leaves the road when the normal force reaches zero

Why: Then gravity alone supplies the centripetal force.

\[ g = \dfrac{v^2}{r} \;\Rightarrow\; v = \sqrt{gr} = \sqrt{196} = 14 \text{ m/s} \]

Verify: against experience

Why: At 10 m/s the road pushes back with less than half the weight, which is the light feeling in your stomach at the top of a bump. At 14 m/s it pushes back with nothing, and the car goes airborne. Both make sense, and the normal force is less than m g, never more, at the top of a hill.

HyperPhysics, Mechanics — Newton's laws, friction and circular motion vertical circular motion

68. Trap: drawing the centripetal force as an extra arrow

Trap

The trap

A ball on a string whirls in a horizontal circle. Draw its free-body diagram.

Draw tension inward, weight down, and a separate centripetal force inward

Why: Three forces, so the student writes tension plus the centripetal force equals m v squared over r.

Solve for the tension

Why: The answer comes out too small, because the same force has been counted twice.

The fix

A ball on a string whirls in a horizontal circle. Draw its free-body diagram.

Draw only real forces: tension along the string and the weight

Why: Ask of each arrow: what exerts it? Nothing exerts a separate centripetal force.

Then write the second law toward the centre

Why: The inward parts of the real forces add up to m v squared over r. Centripetal is a description of the net force, never an item on the list of forces.

69. Push it: a banked curve with no friction

Edge cases

Engineers bank curves so cars can turn even on ice.

Discussion prompt

A curve of radius 50 m is designed for 15 m/s with no friction at all. What bank angle does it need, and what happens to a car going faster?

Hint: Split the normal force into a vertical part that balances the weight and a horizontal part that turns the car.

Answer:

Tilting the road tilts the normal force inward, so its horizontal part can supply the centripetal force. Its vertical part holds up the weight.

Dividing the two equations gives the tangent of the angle equal to v squared over r g: 225 divided by 490, which is 0.459, so the angle is about 24.7 degrees.

A car going faster needs more inward force than the normal force can give at that angle, so with no friction it slides up and out of the curve. With friction it can go a little faster, because friction then points down the slope and adds to the inward force.

70. Check: the top of a loop

Check

Solve it on paper before you click.

Check your understanding

A roller coaster car rounds the top of a vertical loop of radius 10 m, upside down. What is the minimum speed at the top for the car to stay on the track?

  • A. About 9.9 m/s (correct)
  • B. About 14 m/s
  • C. Zero, the track holds the car in
  • D. About 98 m/s

Answer: A

Why: At the top both the weight and the track's normal force point down, toward the centre. At the minimum speed the track pushes with nothing, so gravity alone supplies the centripetal force: g equals v squared over r, giving v as the square root of 98, about 9.9 m/s. Any slower and gravity pulls the car into a tighter curve than the track, so it falls away.

Why B tempts people
That is the square root of 2 g r, which comes from an energy argument about a different question. The condition here is simply that the normal force reaches zero.
Why C tempts people
A track can push on the car but cannot pull it. At low speed the car would fall away from the track, which is why loops have a minimum speed.
Why D tempts people
That is g times r, without the square root. Its units are metres squared per second squared, not metres per second, which flags the slip.

71. Part 10 — Universal gravitation

Section

Where g comes from

72. Newton's law of gravitation

Concept

Every pair of masses attracts with a force proportional to both masses and inversely proportional to the square of the distance between their centres. The constant G is tiny, which is why you do not feel the pull of the person next to you.

\[ F_g = \dfrac{G m_1 m_2}{r^2} \qquad G = 6.67 \times 10^{-11} \text{ N m}^2/\text{kg}^2 \]

Divide the force on a small mass by that mass and you get the gravitational field, the acceleration of anything dropped there. At the Earth's surface that is the familiar 9.8.

\[ g = \dfrac{GM}{r^2} \]

College Board, AP Physics 1: Algebra-Based Course and Exam Description Topic 2.8, Gravitational Force

73. Worked example: g at the surface and on the space station

Worked example

The Earth's mass is 5.97 times ten to the 24 kg and its radius 6.37 times ten to the 6 m. Find g at the surface and at the space station, 400 km up.

Figure (svg): A graph of g against distance from the Earth's centre falling as one over r squared, with the surface, the space station and twice the radius marked

At the surface, r is the Earth's radius

Why: The distance in the law is measured from the centre of the Earth, not from the ground.

\[ g = \dfrac{(6.67\times10^{-11})(5.97\times10^{24})}{(6.37\times10^{6})^2} = 9.81 \text{ m/s}^2 \]

At the station, r is the radius plus the altitude, 6.77 times ten to the 6 m

Why: Only the distance changed, so scale by the square of the ratio of distances rather than recomputing.

\[ g_{\text{ISS}} = 9.81 \left(\dfrac{6.37}{6.77}\right)^2 = 8.68 \text{ m/s}^2 \]

Verify: with the inverse-square pattern

Why: Doubling the distance from the centre should quarter g, giving 2.45 m/s squared at one Earth radius up, and the graph shows exactly that. The station is only 6 per cent farther out than the surface, so g there is only about 11 per cent less, consistent with the 8.68.

OpenStax, College Physics 2e — chapters 4, 5 and 6 chapter 6.5

74. Estimate: the pull between two cars

Estimation

Get a feel for how weak gravity is between ordinary objects.

Predict first

Two 1000 kg cars are parked with their centres 1 m apart. Roughly how strong is the gravitational pull between them?

  • About 10 N
  • About 0.01 N
  • About a ten-thousandth of a newton
  • About a billionth of a newton

Correct: About a ten-thousandth of a newton

Why: G times 1000 times 1000 over 1 squared is 6.67 times ten to the minus 5, about 0.00007 N, less than the weight of a grain of sand. Gravity is only noticeable when one of the masses is planet-sized, which is why the weight of an object is effectively just the pull of the Earth.

75. Does the Earth fall toward you?

Real world

A third-law question dressed up as a gravity question.

Discussion prompt

You jump off a wall. The Earth pulls you down with 588 N. By the third law you pull the Earth up with 588 N. Why does the Earth not visibly move?

Hint: Equal forces, so compare the masses in the second law.

Answer:

It does move, but by the second law its acceleration is 588 N divided by 5.97 times ten to the 24 kg, about ten to the minus 22 m/s squared.

Over the half-second of your fall that moves the Earth by far less than the width of an atom. The forces are equal; the accelerations differ by the ratio of the masses.

This is the truck and the car again, at an extreme: equal forces, wildly unequal effects, because the masses are wildly unequal.

76. Part 11 — Putting it on your homework

Section

Consolidation

77. The whole unit as one page

Pattern

Everything above, compressed to what you would want on an index card.

situationwhat to do firstthe trap
at rest or constant velocitynet force zero on each axisinventing a force of motion
box on a level floorvertical axis gives the normal forceassuming normal equals m g with an angled pull
elevator or scalescale reading is the normal forceusing direction of motion, not acceleration
ropes and pulleyswhole system for a, one block for Tsetting tension equal to a hanging weight
friction, nothing movingstatic friction from the second lawusing the coefficient times N
inclineaxes along and across the slopeswapping sine and cosine
circlenet inward force is m v squared over rdrawing an extra centripetal arrow
gravity far from Earthg falls as one over r squaredusing the altitude instead of the distance to the centre

Nearly every row is resolved by writing the perpendicular equation first, then the equation along the acceleration.

College Board, AP Physics 1: Algebra-Based Course and Exam Description Unit 2

78. The six forces, side by side

Comparison

Fill the blank from the pattern rather than from memory.

Comparison matrix

forcedirectionhow to find its size
weighttoward the Earth's centrem g
normalperpendicular out of the surfacefrom the second law on the perpendicular axis
tensionalong the rope, away from the objectfrom the second law
kinetic frictionagainst the slidingcoefficient times the normal force
static frictionagainst the attempted slidingfrom the second law, up to its maximum
springback toward natural lengthk times the stretch

Only three of the six have a formula you can just write down: weight, kinetic friction and the spring force. The other three are reactive, and must be found from the second law. Knowing which is which prevents most of the errors in this deck.

79. Teach the free-body diagram

Explain it

Say it out loud, to a person or to an empty room. If you can teach it, you can do it under exam pressure.

Discussion prompt

In under a minute, teach someone how to draw a correct free-body diagram for any object.

Hint: Weight first, then go round everything touching it.

Answer:

Draw the object as a dot. Add its weight, straight down.

Then go round everything touching it. Each surface can give a normal force, out of the surface, and a friction force, along it. Each rope gives a tension, along the rope away from the object. Each spring gives a spring force.

Stop there. Every arrow must name what exerts it, and nothing else goes on: no force of motion, no inertia, no centripetal force, no forces the object exerts on other things.

80. Retrieval: eight answers, no notes

Warm-up

Close the deck. This is worth several times what rereading is worth.

Discussion prompt

From memory: the five steps; when the normal force equals m g; what the third-law pairs are for a book on a table; the scale reading in an elevator accelerating up; why static friction is not always the coefficient times N; which component of the weight gets the sine on a slope; what supplies the centripetal force on a flat curve; and how g changes if you double your distance from the Earth's centre.

Hint: Five steps, one condition, two pairs, one formula, one ceiling, one component, one force, one fraction.

Answer:

System, free-body diagram, axes along the acceleration, second law per axis, solve and check a limit.

Only when nothing else acts perpendicular to the surface and nothing accelerates that way.

Earth on book with book on Earth, and table on book with book on table. Not weight with normal.

More than the weight: m times the quantity g plus a.

Because that is only its maximum; below slipping, static friction is whatever balances the other forces.

The component along the slope, m g sin theta.

Static friction from the road.

It drops to a quarter.

81. Build your own index card

Connect it up

Do this before the next session and bring it.

Draw it

Draw four free-body diagrams, with every arrow labelled by its agent and coloured the way this deck colours them: a box pulled across a rough floor by a rope at an angle, the modified Atwood machine with both blocks, a block sliding down a rough incline with its axes tilted, and a car at the top of a hill. Under each, write the one equation you would write first.

If those four diagrams come easily, the unit has landed. If one of them is hard, that is exactly the section to revisit before the homework.

82. Exit ticket: where should the next session go?

Exit ticket

We can spend the next hour wherever it helps most.

Predict first

What would be most useful next time?

  • More pulley and connected-object problems
  • Friction and inclines together, the hardest combination
  • Circular motion problems
  • Working through your actual homework as it is set
  • Getting ahead into work and energy

Correct: Whichever you pick is what I will prepare.

Why: Inclines with friction and connected objects together are where most marks are lost on the AP exam, so that is a strong choice if the homework allows. Working through the real homework is usually best once the method is in place. Energy, Unit 3, solves some of these same problems far more quickly, which is worth seeing once the force method is solid.

83. What you can do now

Recap

One law, one method, applied to a steadily harder set of pictures.

quantityrulefound from
net forcem a, per axisthe free-body diagram
weightm ga formula
normal forcewhatever is neededthe perpendicular axis
kinetic frictioncoefficient times Na formula, once N is known
static frictionup to coefficient times Nthe second law
spring forcek xa formula
centripetal forcem v squared over rthe net inward force, not a new arrow
gravityG m m over r squareda formula

College Board, AP Physics 1: Algebra-Based Course and Exam Description Unit 2 — with OpenStax chapters 4 to 6 for extra worked practice

Sources

  1. College Board, AP Physics 1: Algebra-Based Course and Exam Description
  2. OpenStax, College Physics 2e — chapters 4, 5 and 6
  3. HyperPhysics, Mechanics — Newton's laws, friction and circular motion

Want this taught 1-on-1? Alexander tutors AP Physics 1 — $55/session, free consultation.

Book on Wyzant · Text (657) 465-8108